Stair Stringer Calculator
Calculate stair stringer length and cut layout from rise, run and number of steps.
What this calculator measures
A stair stringer is the sloped board that supports the treads and risers. Its length is the hypotenuse of the right triangle formed by the total rise and total run. This calculator computes the stringer length, the total rise, the total run and the number of steps, so the stringer can be cut from stock lumber.
The tool keeps each value separate, so the layout can be checked against a framing square.
How the calculation works
The calculator multiplies the number of steps by the rise and run per step to get the total rise and total run, then computes the hypotenuse for the stringer length. It also reports the number of treads and risers.
Because the stringer is cut from stock lumber, the result should be compared against standard lumber lengths, with extra for the bottom cut and top bearing.
Worked example
Using 14 steps, 7 in rise and 10 in run, the calculator returns:
Fourteen steps at 7 in rise and 10 in run give a total rise of 98 in and a total run of 140 in. The stringer must be at least 14.24 ft long before cuts. Order a 16 ft board and cut to length.
Reading the result: the stringer length is the number to check against stock lumber length; the total rise and run are the numbers to check against the opening.
Inputs, field by field
- Number of steps: The number of risers from the lower to the upper level.
- Rise per step (in): The vertical height of each step.
- Run per step (in): The horizontal depth of each tread.
Why the inputs matter
Step count, rise and run together determine the stringer length. The length grows with both the rise and the run.
Units and conversion checks
Rise and run in inches. The calculator reports feet alongside.
Common mistakes with this calculation
- Using the total rise instead of the per-step rise.
- Forgetting to add for the bottom cut and top bearing.
- Cutting the stringer to the exact calculated length, which leaves no room for error.
- Ignoring headroom, which must be checked over the entire stair run.
Ordering and materials
Order stringers in the next standard length above the calculated length. Check that the lumber grade is suitable for structural use. Add one extra stringer for defects.
What this calculator does not decide
This tool does not determine code compliance, required headroom, or structural capacity. Those depend on the applicable building code and the project documents. Where safety or regulated construction is involved, the project documents and qualified professionals take precedence.
Field verification checklist
Before cutting, re-measure the rise and run, check the stringer length against stock lumber, and verify headroom over the entire run.
Practical considerations for stair stringers
Stair stringers must be cut from lumber that is free of large knots and defects, since the cuts remove material and weaken the board. Use a higher grade of lumber for stringers than for treads and risers.
The stringer length must be checked against stock lumber lengths, with extra for the bottom cut and top bearing. A stringer that is cut to the exact calculated length leaves no room for error and may not fit.
Headroom must be checked over the entire stair run, not just at the top and bottom. The minimum headroom is typically 6 ft 8 in, and it must be maintained over the entire stair, including the landing.
Detailed guide to stringer budgeting
Stair stringers must be cut from lumber that is free of large knots and defects, since the cuts remove material and weaken the board. Use a higher grade of lumber for stringers than for treads and risers.
The stringer length must be checked against stock lumber lengths, with extra for the bottom cut and top bearing. A stringer that is cut to the exact calculated length leaves no room for error and may not fit.
Headroom must be checked over the entire stair run, not just at the top and bottom. The minimum headroom is typically 6 ft 8 in, and it must be maintained over the entire stair, including the landing.
Related BuildNumeris tools
Construction estimates are interconnected. Open the related tools below to build a connected takeoff.
Practical workflow
Measure the rise and run, calculate the stringer length, check against stock lumber, then cut with allowance for the bottom cut and top bearing.